How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that protects your car from key cloning and hacking. It prevents the engine of your vehicle from starting until it is activated using the PIN code that is as long as 20 characters.
It is not detected by thieves and they are unlikely to be expecting this extra layer of security. Some systems also have an app that allows owners to disarm the immobiliser in case they forget their PIN or to switch to the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is a cutting-edge security system, is able to be integrated directly into the ECU of your vehicle. It offers a discrete barrier against thieves. It is extremely efficient and user-friendly. This makes it a valuable asset to your vehicle's arsenal of security. Like any anti-theft device, it's not foolproof and requires regular maintenance in order to function properly. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network) is a reliable serial network that lets microcontrollers communicate with one another over short distances without the necessity of central control units. It is designed to multiply electrical wiring in vehicles, which saves on copper. It has many advantages, such as low cost and easy use.
The CAN protocol is utilized in the majority of modern vehicles to communicate with the engine management system, transmission controller, steering control module air conditioning controls and many more. It also transmits sensor data including speed sensors and inputs, to control the various functions of the vehicle. The CAN bus is used to monitor these various components, and it can stop the car from starting if they're in danger of failure.
While the CAN bus could be used for a variety of purposes, it's important to understand how it works and how it's secured. The CAN bus is a great way to add new features to your vehicle, but it's essential to secure it from threats such as hackers and other. Installing a firewall, and monitoring your CAN-bus using software is the best way to do this.
Ghost2's control device is hidden in the dashboard or wiring harness, which prevents a thief from physically tampering it. It is impossible to reset a PIN code or emergency code without access to the car.
You can activate Transport Mode when you have to sell your car for service, valet parking or for any other reason. ghost 2 immobiliser cost will disable both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph over a period of 15 minutes.
How to create a PIN code
The Ghost immobiliser shields your vehicle from thieves. The cutting-edge technology uses an PIN code to shut down the engine and stop it from running without the correct code or a valid fob or mobile device. The system's discrete design makes it virtually invisible and offers unrivaled security against theft. The system is TASSA-certified and could save you substantial sums on your car insurance.
During the installation, Ghost enters a "learning mode" to record the sequences of buttons that are pressed to generate your unique pin codes. After the pin code is created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated, the Ghost system will disable the starter motor of your vehicle until a valid PIN has been entered or the vehicle is switched to transport mode. This makes it very difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
Installing ghost 2 immobiliser cost is simple, but it is important to follow the precise instructions in the user manual to ensure that it operates properly. Hand tools are essential in making the perfect connections, and a multimeter can aid in checking the electrical parameters. Insulation tape, heat shrink tubing and cable ties are a good option to shield exposed wiring. Be sure to test the system on a regular basis to find any problems and potential mistakes.
After the installation is completed it is crucial to conduct a final test of the system prior to turning on the ignition in your vehicle. Ghost immobilisers will re-arm themselves after a period of 3 to 30 seconds depending on the model of your car. The system also comes with a Service/Valet Mode that lets you temporarily disable the system to service or valet parking.
The immobiliser can be hidden under the dashboard or the steering wheel. It is recommended to use a small bit of paint or duct tape to mark the CAN H and L wires so that you can easily identify the wires during testing. The CAN H and L wires must also be connected to an electrical source that delivers continuous 12V. It is also crucial to check the connections again after testing, since misidentifying these wires can cause the system to fail.
Activating the system
A ghost immobiliser stops your car from starting until you press a few buttons inside the vehicle, typically on the steering wheel or door panel, or the central console. The sequence can be changed by the user if needed. Once the system is activated, it is not able to be disabled by thieves, making it a good option for anyone looking to secure their vehicle from theft.
The system is designed not to be able to be detected by modern diagnostic and code-grabbing technology. It doesn't emit radio frequency either which makes it more difficult for thieves detect.
If the device is identified, it will stop the engine from starting and sound an alarm that is loud enough to scare off thieves. The device can be used to track the location of a car which can aid in the search for the vehicle in the event that it has been taken.
Contact ghost autowatch immobiliser for a estimate or to discuss your options in an immobiliser that is ghost-like. We are fully trained to install a ghost immobiliser on your vehicle and will ensure that it is tucked away in a remote area. We can also install other security measures, including the kill switch and wheel lock to ensure your vehicle is secure from theft.
Disarming the System
If you own a Ghost immobiliser that is fitted to your vehicle, it's essential to know how you can disable it. It can be used in the event you forget your keys or your battery is dead. The system is based on an individual PIN code that only you know, so the immobiliser will not start your vehicle without entering this code. The simplest method to enter the code is to press a series of buttons on your dashboard or the steering wheel. This is a much easier method than using the key fob and it also keeps anyone from copying your remote.
In contrast to some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to function. Its most distinctive characteristic is that it disables the engine without affecting functions of the vehicle. This makes it extremely difficult for thieves to use signal boosters or duplicate keys to car keys. Additionally, it doesn't emit radio frequencies, which means thieves aren't able to detect the system.
The Ghost system also comes with the Transport Mode, which allows you to temporarily disable the security system for situations such as transportation or servicing. This feature is great if you are lending your vehicle to someone else, without sharing your PIN code, or if your vehicle needs to be secured while you drive it. Press the service button five times over 2 seconds to activate Transport Mode. The Ghost system will confirm activation via 5 indication signals.
After you're done, make sure to save the emergency code in a safe place away from your vehicle. If you are ever locked out of your car you can contact the technician or company who installed the system and they'll provide you with the code. If they are not able to contact you then you can try contacting an authorized dealer but this would require verification procedures and could incur additional charges.
This system is not only practical, but it can also protect your vehicle from theft and reduce insurance costs. Many insurance companies offer lower premiums or financial incentives to install this anti-theft system.